MeshCore

Commit Graph

Author	SHA1	Message	Date
Wessel	9e91dee68e	Merge `7b7b56beb0` into `adc631f315`	4 days ago
Liam Cottle	adc631f315	Merge pull request #3048 from entr0p1/fix/startota-failure-recovery nRF52840 "start ota" Failure Recovery	5 days ago
entr0p1	4050b7d526	nRF52840 "start ota" Failure Recovery If Bluefruit.begin fails, BLE OTA mode won't actually start and the board might require a reboot to reattempt. Fixes: - Bluefruit.begin returns false in NRF52Board.startOTAUpdate if OTA mode fails to start. User is notified of the fault through existing error message in CommonCLI and can reattempt "start ota" command.	5 days ago
ripplebiz	c86e63d2f5	Merge pull request #2982 from meshcore-dev/config-serializer Config serializer	6 days ago
ripplebiz	301bc10dd3	Merge pull request #3034 from meshcore-dev/ui-color-refactor UI color refactor	6 days ago
Liam Cottle	cee6d94894	Merge pull request #3040 from blowfishpro/docs/FixPayloadDocsFormatting Increase header levels on "Payloads" documentation page to fix table of contents	6 days ago
Talia	b62b421456	docs: increase header levels on payloads page to fix table of contents mkdocs will only consider the first H1 (if any) and subheaders under it for the table of contents this increases the header levels of everything below "important concepts" by 1 so that the table of contents correctly resolves them	1 week ago
ripplebiz	e3de413a69	Merge pull request #3036 from oltaco/add-preamble-irq-flag Fix missing PREAMBLE_DETECTED IRQ flag for all radio wrappers	1 week ago
taco	6b83de507d	SX1268: add PREAMBLE_DETECTED to reported irq flags	1 week ago
taco	0d2b988f24	STM32WLx: add PREAMBLE_DETECTED to reported irq flags	1 week ago
taco	c56928347f	LLCC68: add PREAMBLE_DETECTED to reported irq flags	1 week ago
taco	ea5d7c8bf5	LR1110: add PREAMBLE_DETECTED to reported irq flags	1 week ago
taco	fae4803158	SX1262: add PREAMBLE_DETECTED to reported irq flags	2 weeks ago
Scott Powell	f83ad03e5e	* T114 display fix	1 week ago
Scott Powell	0c04a47355	* fixed for mono ST7789 display driver	1 week ago
Scott Powell	3857f45826	* monochrome displays now do _not_ invert titlebar	1 week ago
Scott Powell	ee79df4c4f	Merge branch 'dev' into config-serializer # Conflicts: # test/mocks/Arduino.h # test/mocks/Stream.h	1 week ago
Liam Cottle	e780cca237	Merge pull request #3033 from liamcottle/board/lilygo-tbeam-sx1276 Increase LilyGo T-Beam SX1276 channels from 8 to 40	1 week ago
liamcottle	520fa77f4f	increase tbeam sx1276 max group channels from 8 to 40	1 week ago
Liam Cottle	d531a98da1	Merge pull request #2819 from ViezeVingertjes/fix/kiss-modem-usb-backpressure fix: prevent ESP32 KISS modem stalls under USB backpressure	1 week ago
Liam Cottle	8a69f34101	Merge pull request #3023 from agessaman/fix/rx-boosted-gain fix(room_server): support RX boosted gain	2 weeks ago
Wessel Nieboer	7b7b56beb0	Fix CONTACT_FLAG_AEAD bit collision with telemetry permissions	2 months ago
Wessel Nieboer	b3c4adada1	prevent rekeying wrong contact	5 months ago
Wessel Nieboer	1120602703	mode-aware max path calculation (AEAD-4 vs ECB)	5 months ago
Wessel Nieboer	d8e7d9693e	clarify this might roll-over	5 months ago
Wessel	9b1320a899	Apply suggestions from code review Co-authored-by: J.C. Jones <[email protected]>	5 months ago
Wessel Nieboer	61a664a955	Address comments	6 months ago
Wessel Nieboer	b3492dcc4c	check if contact still exists	6 months ago
Wessel Nieboer	ef5079455e	Fix dirty session keys.	6 months ago
Wessel Nieboer	60eb092ab8	Allow persisting more session to flash	6 months ago
Wessel Nieboer	fc944c0825	Implement session keys using	6 months ago
Wessel Nieboer	9ce710ebd1	Persist AEAD-4 nonces to flash across reboots Prevent nonce reuse after reboots by persisting per-peer nonce counters to a dedicated /nonces (companion) or /s_nonces (server) file. On dirty reset (power-on, watchdog, brownout), nonces are bumped by NONCE_BOOT_BUMP (100) to cover any unpersisted messages. Clean wakes (deep sleep, software restart) load nonces as-is. - Add nonce persistence to BaseChatMesh (companion) and ClientACL (server) - Add wasDirtyReset() helper to ArduinoHelpers.h for platform-specific reset reason detection (ESP32/NRF52) - Add onBeforeReboot() callback to CommonCLI for pre-reboot nonce flush - Wire nonce persistence into all firmware variants: companion radio, repeater, room server, and sensor - Only clear dirty flag on successful file write	6 months ago
Wessel Nieboer	fc3eb1ecb4	Add comment about ECB path failure	6 months ago
Wessel Nieboer	7682782405	Harden AEAD-4 bounds checks and add nonce wrap logging - Fix potential unsigned overflow in createDatagram size check by subtracting constants from MAX_PACKET_PAYLOAD instead of adding to data_len - Add upper-bound validation on src_len and assoc_len in aeadEncrypt and aeadDecrypt - Log peer name on AEAD nonce wraparound for debug builds	6 months ago
Wessel Nieboer	dc2668c6d3	Support AEAD responses in repeater/room/sensor	6 months ago
Wessel Nieboer	c8d4b250f4	Fix AEAD-4 assoc data mismatch — route type bits set after encryption The header's route type bits (PH_ROUTE_MASK) are zero when createDatagram/createPathReturn encrypt with AEAD, but get changed to ROUTE_TYPE_FLOOD (1) or ROUTE_TYPE_DIRECT (2) by sendFlood/sendDirect afterwards. The receiver builds assoc from the received header (with route bits set), so the tag check always fails and every AEAD packet is silently dropped. Mask out route type bits in assoc data on all 5 encrypt/decrypt sites. Also track AEAD decode success to enable peer capability auto-detection.	6 months ago
Wessel Nieboer	cf04aaa954	Fix AEAD-4 payload size check and nonce wrap-around	6 months ago
Wessel Nieboer	5f1628ca1d	Enable AEAD-4 sending to peers that advertise support Send ChaChaPoly-encrypted messages to peers with CONTACT_FLAG_AEAD set, and try AEAD decode first for those peers (avoiding 1/65536 ECB false-positive). Legacy peers continue to use ECB in both directions. - Add aead_nonce parameter to createDatagram/createPathReturn (default 0 = ECB) - Add getPeerFlags/getPeerNextAeadNonce virtual methods for decode-order selection - Add ContactInfo::nextAeadNonce() helper (returns nonce++ if AEAD, 0 otherwise) - Update all BaseChatMesh send paths to pass nonce for AEAD-capable peers - Adaptive decode order: AEAD-first for known AEAD peers, ECB-first for others	6 months ago
Wessel Nieboer	33c01e50b9	Add ChaChaPoly AEAD-4 decryption support (Phase 1) Add ChaCha20-Poly1305 AEAD decryption with 4-byte auth tag for peer messages and group channels, falling back to ECB for backward compatibility. Sending remains ECB-only in this phase. - Per-message key derivation: HMAC-SHA256(secret, nonce\|\|dest\|\|src) - Direction-dependent keys prevent bidirectional keystream reuse - 12-byte IV from nonce + dest_hash + src_hash - Advertise AEAD capability via feat1 bit 0 in adverts - Track peer AEAD support in ContactInfo.flags - Seed aead_nonce from HW RNG on contact creation and load	6 months ago
Scott Powell	56274db4ad	* build fixes for old ESP32 boards	2 weeks ago
Scott Powell	a96a66aa99	* build fixes for NullDisplayDriver	2 weeks ago
Scott Powell	b8504e55c6	* refactor of Color mapping in UITasks / DisplayDrivers * color displays now with a new light theme	2 weeks ago
agessaman	a71cc23854	fix(room_server): support RX boosted gain The room server never supported RX boosted gain, while the repeater does. Three consequences on SX1262/SX1268 boards: - boosted gain was never applied to the radio at boot, so a room server ran in power-saving RX mode while an identical repeater ran boosted - a real receive-sensitivity difference with nothing pointing at it - _prefs.rx_boosted_gain was never initialised (the prefs are memset to 0 before defaults are set), so it defaulted to off - 'set radio.rxgain on' replied "Error: unsupported" but CommonCLI had already written the value to prefs and saved them, so a stale setting survived reboot and was never applied Mirror the repeater's implementation: initialise the pref default under the same USE_SX1262/USE_SX1268 and SX126X_RX_BOOSTED_GAIN guards, apply it during radio init, and override setRxBoostedGain() so the CLI reports success and takes effect. Built Heltec_v3_room_server (SX1262) and LilyGo_T3S3_sx1276_room_server (guards compile out cleanly).	2 weeks ago
Scott Powell	78240e9477	* optimised: value-init not needed	2 weeks ago
ripplebiz	4157e43ace	Merge pull request #3005 from axhoff/agent/fix-ble-reconnect Fix bonded BLE reconnects on ESP32	2 weeks ago
ripplebiz	8b048ab19a	Merge pull request #3007 from axhoff/agent/synchronize-ble-receive-queue Synchronize the ESP32 BLE receive queue	2 weeks ago
ripplebiz	6a15e1712b	Merge pull request #3006 from axhoff/agent/fix-heltec-v4-usb-companion Enable hardware USB serial on Heltec V4	2 weeks ago
Liam Cottle	7124fa1439	Merge pull request #2815 from UltimateCodeWarrior/fix/tbeam-supreme-v3-oled-i2c Fix blank OLED on T-Beam Supreme V3 (I2C bus init + 0x3D address)	2 weeks ago
Alexander Hoffer	4d4d7c3746	refactor: use FreeRTOS BLE receive queue	2 weeks ago
=UltimateCodeWarrior	0de2b4fc5f	Move Supreme OLED address to variant config Keep SH1106Display generic by relying on DISPLAY_ADDRESS while the T-Beam Supreme variant declares its 0x3D OLED address.	2 weeks ago

1 2 3 4 5 ...

3247 Commits (9e91dee68e84224e8c5df9762a931bf3a3253d94) All Branches Search

3247 Commits (9e91dee68e84224e8c5df9762a931bf3a3253d94)

All Branches