MeshCore

Commit Graph

Author	SHA1	Message	Date
João Brázio	75895895f0	Add USE_SX1262 flag to multiple platformio.ini configurations	3 months ago
Wessel Nieboer	0e62240119	Set AUTO_OFF_MILLIS to 0 for E213, E290	3 months ago
Wessel Nieboer	696323c11b	Fix Heltec E213 and E290 e-ink board builds	3 months ago
Sybren A. Stüvel	9349e6ab6b	SenseCap Solar: fix use of LED_GREEN `5188221584` changed LED_RED/GREEN to LED_WHITE/BLUE, but didn't convert all uses of LED_GREEN.	3 months ago
MGJ	307142986f	Support for GAT562 30S Mesh Kit device	3 months ago
MGJ	82689512f8	Fix incorrect comments	3 months ago
MGJ	e9ff0bd9b0	Remove GAT562 Mesh Tracker Pro device radio preset	3 months ago
Sam Schlegel	bfdbcd85e8	Add nrf52 power management for RAK3401	3 months ago
MGJ	011c5ba102	Add support for the GAT562 Mesh Tracker Pro device	3 months ago
MGJ	dc48126baf	Add support for the GAT562 Mesh Tracker Pro device	3 months ago
Confi	5188221584	sensecap_solar: fix LED definitions (white=11, blue=12)	4 months ago
Quency-D	7a8370fa69	Fixed a bug in the LORA_TX_POWER comment.	3 months ago
Quency-D	cdca79540f	Update Heltec Tracker v2 to version KCT8103L.	3 months ago
João Brázio	9a95e25ef2	Remove unused RX boosted gain mode functions and related preprocessor directives across multiple variants	3 months ago
Wessel Nieboer	67d22401b1	Pass rtc_clock to all MicroNMEALocationProvider instances Enable GPS time synchronization across all variants by passing &rtc_clock to MicroNMEALocationProvider. When GPS gets a valid fix, the RTC clock is now updated automatically every 30 minutes. Updated 16 variants: rak4631, lilygo_tbeam_SX1262, rak_wismesh_tag, lilygo_tbeam_supreme_SX1262, thinknode_m3, heltec_v4, thinknode_m1, lilygo_tbeam_SX1276, meshadventurer, nano_g2_ultra, heltec_v3, promicro, xiao_c3, heltec_tracker_v2, keepteen_lt1, heltec_mesh_solar.	5 months ago
Wessel Nieboer	c0c9c17cf5	and buildscript	3 months ago
Wessel Nieboer	780720c117	and board!	3 months ago
Wessel Nieboer	90fcd1043f	Fix ikoka handheld build The extends was wrong.	3 months ago
Wessel Nieboer	59d9770ab9	Add GPS support Heltec Wireless Tracker v1.x Pin mapping verified against HTIT-Tracker V0.5 schematic: - GPIO35 (GPS_EN): N-ch MOSFET drives P-ch high-side switch, active HIGH - GPIO36 (GPS_RST): hardware reset, active LOW - GPIO33/34: UART TX/RX Delegates power management to MicroNMEALocationProvider begin()/stop() which independently controls GPS power via GPS_EN and shares VEXT with the display through RefCountedDigitalPin.	5 months ago
Wessel Nieboer	49d8313501	Fix pin mapping & TX switch (it's DIO2)	3 months ago
Wessel Nieboer	5a5568ed56	Drive CTX low first	3 months ago
Wessel Nieboer	ac2aa03b09	Add SX126X_REGISTER_PATCH for RAK3401	3 months ago
Wessel Nieboer	70f1ad4aeb	Fix RAK3401 SKY66122-11 FEM control: enable CSD/CPS for proper PA and LNA operation The RAK13302 1W module uses a Skyworks SKY66122-11 front-end module with three digital control pins (CSD, CTX, CPS) that must be actively driven by the host MCU. The previous code only managed CTX (GPIO 31) — toggling it for TX/RX — but never initialized CSD (GPIO 24) or CPS (GPIO 21), leaving them floating with no pull-up/pull-down resistors on the PCB. With floating CSD and CPS, the SKY66122 was in an undefined operating mode: - The 30 dB TX PA may not have been reliably engaging - The 16 dB RX LNA was never reliably active, degrading receive sensitivity	3 months ago
Wessel Nieboer	2bb6f636a4	Add 1ms delay after powering PA (cold-boot)	4 months ago
Wessel Nieboer	329e408197	Hold GC1109 PA_POWER during deep sleep for LNA RX wake The GC1109 FEM needs its VFEM_Ctrl pin held HIGH during deep sleep to keep the LNA active, enabling proper RX sensitivity for wake-on-packet. Without this, the LNA is unpowered during sleep and RX wake sensitivity is degraded by ~17dB. Release RTC holds in begin() after configuring GPIO registers (not before) to ensure glitch-free pin transitions on wake. Trade-off: ~6.5mA additional sleep current for significantly improved wake-on-packet range.	4 months ago
Specter242	e08dcbdd03	sensecap solar: stabilize wake pin and add button hold poweroff	3 months ago
Specter242	e323755990	sensecap solar: add poweroff command and board power/LED parity	3 months ago
Wessel Nieboer	8bf63256b6	Fix remote LNA toggle bugs: correct register comparison, add missing implementations, wire up companion radio getRxBoostedGain was returned true because both 0x94 (power saving) and 0x96 (boosted gain = 1) return true	3 months ago
Scott Powell	f4748a7f9d	* misc	3 months ago
callum5892	9f4eeeeceb	Added build flags for M5Stack Unit C6L Enabled USB-CDC on boot for M5Stack_Unit_C6L_companion_radio_usb to fix serial connection issues	3 months ago
Sam Koucha	5a885bffe4	Make full use of board's 8MB Flash and add companion WiFI target	3 months ago
Sander van Grieken	3dc14976a0	add companion usb build target for Heltec Wireless Tracker	3 months ago
Kevin Le	13d0dff918	Reverted to use GPIO 17, 18 as I2C for Heltec v4 repeater	4 months ago
Kevin Le	44b80d00c2	Disabled periph_power for Heltec v4's display	4 months ago
Kevin Le	f6603fe7a5	Set back PIN_VEXT_EN_ACTIVE=HIGH	4 months ago
3DPGG	3e53df5082	Fix LilyGo_TLora_V2_1_1_6_terminal_chat build This change addresses two issues. The first is that the LilyGo_TLora_V2_1_1_6_terminal_chat build would try to compile simple_repeater/MyMesh.cpp. All other examples of terminal chat targets are instead building simple_secure_chat/main.cpp . This change would align this build to the rest of the builds. The second issue, found during the course of investigating the first, stems from simple_repeater/MyMesh.cpp using the MAX_NEIGHBOURS #define to control whether the neighbor list is kept. Repeaters that keep this list must define this value, and if the value is not defined, then all neighbor-related functionality is compiled out. However, the code that replies to REQ_TYPE_GET_NEIGHBOURS did not properly check for this #define, and thus any target that compiles simple_repeater/MyMesh.cpp without defining MAX_NEIGHBOURS would get an undefined variable compilation error. As a practical matter though, there are no targets that compile simple_repeater/MyMesh.cpp AND do not define MAX_NEIGHBOURS, except this build due to the first issue. As a result, the second issue is addressed only as a matter of completeness. The expected behavior with this change is that such a repeater would send a valid reply indicating zero known neighbors.	4 months ago
recrof	cafc212bb2	fix M5Stack Unit M6L build errors	4 months ago
Rastislav Vysoky	beff18c53b	fix usb and build for rak 3112	4 months ago
dylan	f720338c03	Fix WioTrackerL1 BLE companion: route sensors to Grove I2C bus (Wire1) Sensors connected via the Grove I2C connector (D18/D17) were not detected because the firmware scanned the OLED I2C bus (Wire, D14/D15) by default. Adding ENV_PIN_SDA/SCL flags directs EnvironmentSensorManager to use Wire1, matching the physical Grove connector pinout. Co-Authored-By: Claude Opus 4.6 <[email protected]>	4 months ago
João Brázio	f4951d0895	Fix typo with USE_SX1262/SX1268	4 months ago
João Brázio	71136671bd	Implement remote lna toggle cli cmd	4 months ago
Snayler	810fd561d2	Enable TX LED for LilyGo LoRa32 V2.1_1.6 Working on my device, green TX LED starts blinking every time I transmit	4 months ago
Thane Gill	31a2e74ada	Correct manufacturer name 'Elecrow ThinkNode M5'	4 months ago
João Brázio	fcfbb458f8	Refactor environment names and build flags for RAK variants	4 months ago
Wessel Nieboer	23b4baa066	Enable register patch heltec tracker v2	4 months ago
ViezeVingertjes	5dcc377b77	Rewrite KISS modem to be fully spec-compliant	4 months ago
Wessel Nieboer	d0720c63c2	Allow negative tx power Like SX1262 allows -9 dBm lowest, some allow lower but that probably isn't useful	5 months ago
Marnick Hartgers	0a66dee990	fixed build without ENV_INCLUDE_GPS	4 months ago
João Brázio	5cb26b91f6	Refactor Heltec T114 sensor management	4 months ago
agessaman	0fb570338f	fix(kiss): periodic noise floor calibration and AGC reset - Trigger noise floor calibration every 2s and AGC reset every 30s in main loop. - Reorder loop to match Dispatcher: calibrate + radio.loop() before AGC reset and recvRaw() so RSSI is never sampled right after startReceive(). - Update protocol doc with calibration intervals and typical noise floor range. - Variant platformio.ini updates (heltec_v3, rak4631).	4 months ago

1 2 3 4 5 ...

932 Commits (31007d9790d247f1f203a0c2222da116a019878f)