mirror of https://github.com/meshcore-dev/MeshCore
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
87 lines
2.2 KiB
87 lines
2.2 KiB
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
|
|
#include "RAK4631Board.h"
|
|
|
|
#ifdef BOOT_DIAG
|
|
// Diagnostic LED blink: N short blinks on green LED to indicate boot stage
|
|
static void diag_blink(uint8_t count) {
|
|
pinMode(PIN_LED1, OUTPUT);
|
|
for (uint8_t i = 0; i < count; i++) {
|
|
digitalWrite(PIN_LED1, HIGH);
|
|
delay(100);
|
|
digitalWrite(PIN_LED1, LOW);
|
|
delay(150);
|
|
}
|
|
delay(300);
|
|
}
|
|
#else
|
|
#define diag_blink(n) ((void)0)
|
|
#endif
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Static configuration for power management
|
|
// Values set in variant.h defines
|
|
const PowerMgtConfig power_config = {
|
|
.lpcomp_ain_channel = PWRMGT_LPCOMP_AIN,
|
|
.lpcomp_refsel = PWRMGT_LPCOMP_REFSEL,
|
|
.voltage_bootlock = PWRMGT_VOLTAGE_BOOTLOCK
|
|
};
|
|
|
|
void RAK4631Board::initiateShutdown(uint8_t reason) {
|
|
// Disable LoRa module power before shutdown
|
|
digitalWrite(SX126X_POWER_EN, LOW);
|
|
|
|
if (reason == SHUTDOWN_REASON_LOW_VOLTAGE ||
|
|
reason == SHUTDOWN_REASON_BOOT_PROTECT) {
|
|
if (!configureVoltageWake(power_config.lpcomp_ain_channel, power_config.lpcomp_refsel)) {
|
|
NVIC_SystemReset();
|
|
}
|
|
}
|
|
|
|
enterSystemOff(reason);
|
|
}
|
|
#endif // NRF52_POWER_MANAGEMENT
|
|
|
|
void RAK4631Board::begin() {
|
|
diag_blink(1); // Stage 1: entering begin()
|
|
|
|
#ifdef DISABLE_DCDC
|
|
NRF52Board::begin();
|
|
#else
|
|
NRF52BoardDCDC::begin();
|
|
#endif
|
|
|
|
diag_blink(2); // Stage 2: board base init done
|
|
|
|
pinMode(PIN_VBAT_READ, INPUT);
|
|
#ifdef PIN_USER_BTN
|
|
pinMode(PIN_USER_BTN, INPUT_PULLUP);
|
|
#endif
|
|
|
|
#ifdef PIN_USER_BTN_ANA
|
|
pinMode(PIN_USER_BTN_ANA, INPUT_PULLUP);
|
|
#endif
|
|
|
|
#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
|
|
Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
|
|
#endif
|
|
|
|
Wire.begin();
|
|
|
|
diag_blink(3); // Stage 3: I2C done, about to configure LoRa power
|
|
|
|
pinMode(SX126X_POWER_EN, OUTPUT);
|
|
#if defined(NRF52_POWER_MANAGEMENT) && !defined(DISABLE_BOOT_PROTECTION)
|
|
// Boot voltage protection check (may not return if voltage too low)
|
|
// We need to call this after we configure SX126X_POWER_EN as output but before we pull high
|
|
checkBootVoltage(&power_config);
|
|
#endif
|
|
|
|
diag_blink(4); // Stage 4: power check passed
|
|
|
|
digitalWrite(SX126X_POWER_EN, HIGH);
|
|
delay(10); // give sx1262 some time to power up
|
|
|
|
diag_blink(5); // Stage 5: board.begin() complete
|
|
}
|