MeshCore

Commit Graph

Author	SHA1	Message	Date
OhYou-0	68360157ec	Add LilyGo T-ETH Elite board support	1 month ago
Rastislav Vysoky	0899f66034	fix: remove sensors from xiao c3 companion because of bootloops	2 months ago
jirogit	230c9af87b	feat: add USB Companion Radio env for Heltec Wireless Paper	2 months ago
Petr Kracik	e6c6282d40	Variants: Enable ElegantOTA on ESP32-C6 devices	2 months ago
Rastislav Vysoky	bd05eca9f5	Add OFFLINE_QUEUE_SIZE=256 for xiao nrf52 companion usb	2 months ago
liamcottle	7d8d66c3e6	fix compilation error in wifi variants due to not enough ram	2 months ago
Malkavien	8056344b86	fix(waveshare-rp2040): add SX126X_RXEN=17 to restore RX sensitivity The Waveshare RP2040-LoRa board has an RF switch with two complementary control lines: - DIO2 (CTRL) -- driven automatically by the SX1262 chip: HIGH on TX, LOW on RX - GPIO17 (!CTRL) -- was not configured in MeshCore, so it floated and the switch never properly selected the LNA/RX path Without this pin driven, the RF switch never switches to RX mode, resulting in completely degraded reception. TX was unaffected because DIO2 alone is sufficient to activate the TX path. Adding SX126X_RXEN=17 lets RadioLib drive GPIO17 as the complement of DIO2, so the switch correctly routes the signal to the LNA on receive. Reference: https://files.waveshare.com/wiki/RP2040-LoRa/Rp2040-lora-sch.pdf	2 months ago
me	d9cfd075a5	fix: remove real WiFi credentials from ThinkNode M5 variant variants/thinknode_m5/platformio.ini contained actual WiFi SSID and password credentials (Livebox-633C) committed by mistake. Replaced with placeholder values consistent with other variants (myssid/mypwd).	2 months ago
Wessel Nieboer	057542625b	Fix T1000E press=high	4 months ago
Wessel Nieboer	0a13ac7fc7	Default button polarity to active-LOW across all firmware types Nearly all LoRa boards use a boot button that pulls to ground when pressed.	4 months ago
jirogit	6769b74df6	fix: correct ADVERT_NAME for Generic ESPNow room server (was 'Heltec Room') env:Generic_ESPNOW_room_svr was using 'Heltec Room' as ADVERT_NAME, causing Generic ESPNow room server nodes to advertise with the wrong device name on the mesh.	2 months ago
jirogit	ce32d91ecb	fix: correct ADVERT_NAME for ThinkNode M5 (was M2) Repeater and Room Server environments in variants/thinknode_m5/platformio.ini were using 'Thinknode M2' as the ADVERT_NAME, causing M5 nodes to advertise with the wrong device name on the mesh. - env:ThinkNode_M5_Repeater: 'Thinknode M2 Repeater' -> 'Thinknode M5 Repeater' - env:ThinkNode_M5_room_server: 'Thinknode M2 Room Server' -> 'Thinknode M5 Room Server'	2 months ago
KPrivitt	27f732653b	Added RAK12035 Soil Moisture and Temperature Sensor (#2223 )	2 months ago
Liam Cottle	fcad0dc7ed	Apply suggestion from @weebl2000 Co-authored-by: Wessel <[email protected]>	2 months ago
Liam Cottle	8fc9e1736c	Apply suggestion from @weebl2000 Co-authored-by: Wessel <[email protected]>	2 months ago
liamcottle	b37201db89	double press top button to go back on gat562 mesh watch	2 months ago
liamcottle	1a897a3b5f	use top button to wake hibernated gat562 mesh watch	2 months ago
Snayler	bfdd5fb571	Fix formatting of ADC_MULTIPLIER definition	2 months ago
Snayler	4b25f0a3df	Add correct ADC_MULTIPLIER definition to Heltec Wireless Paper	2 months ago
Snayler	50e9456f28	Define ADC_MULTIPLIER for adjustable ADC calculation	2 months ago
MGJ	76be69dcde	Reduce unnecessary compilation time	2 months ago
MGJ	cd6c09a0d9	Support for GAT562 Mesh Watch13 device	2 months ago
Jeroen Vermeulen	da689c8e91	Fix default radio.rxgain for Station G2 As @LitBomb pointed out in his [comment](https://github.com/meshcore-dev/MeshCore/issues/2118#issuecomment-4108168109) on #2118 RX Boosted Gain should not be enabled for the Station G2. This change is a fix for #2124 to make the default of `radio.rxgain` to be OFF on the Station G2. This restores the pre-1.14.1 behaviour with the only change being the user is now able to change the setting in the CLI.	2 months ago
Konstantin	c7b8db55e6	Fix typo for ThinkNode M5 room server environment	2 months ago
whywilson	b07ab2bc55	Remove useless define in GAT562_Mesh_EVB_Pro.	3 months ago
Quency-D	f6cfed66b3	add heltec_mesh_node_t096 board.	3 months ago
Robert Ekl	6978fc4bc9	Fix T1000-E pin comments	3 months ago
whywilson	69123ca056	Update GAT562_Mesh_EVB_Pro Config and remove LoRa Specification and change Repeater name.	3 months ago
João Brázio	75895895f0	Add USE_SX1262 flag to multiple platformio.ini configurations	3 months ago
Wessel Nieboer	0e62240119	Set AUTO_OFF_MILLIS to 0 for E213, E290	3 months ago
Wessel Nieboer	696323c11b	Fix Heltec E213 and E290 e-ink board builds	3 months ago
Sybren A. Stüvel	9349e6ab6b	SenseCap Solar: fix use of LED_GREEN `5188221584` changed LED_RED/GREEN to LED_WHITE/BLUE, but didn't convert all uses of LED_GREEN.	3 months ago
whywilson	c994c6206d	Add GAT562 Mesh EVB Pro Repeater and Room Server.	3 months ago
MGJ	307142986f	Support for GAT562 30S Mesh Kit device	3 months ago
MGJ	82689512f8	Fix incorrect comments	3 months ago
MGJ	e9ff0bd9b0	Remove GAT562 Mesh Tracker Pro device radio preset	3 months ago
kelsey hudson	a56419dc21	R1 Neo: Turn off debugging, rtc cleanup	3 months ago
Sam Schlegel	bfdbcd85e8	Add nrf52 power management for RAK3401	3 months ago
MGJ	011c5ba102	Add support for the GAT562 Mesh Tracker Pro device	3 months ago
MGJ	dc48126baf	Add support for the GAT562 Mesh Tracker Pro device	3 months ago
kelsey hudson	5d1f5139ae	Support for muzi works R1 Neo device. Support for R1 Neo hardware. New variant and baseboard class. * Known issues: - power management is not currently supported - power off via long button press is not implemented Add support for Epson Seiko RX8130CE I2C Real-time clock.	3 months ago
Confi	5188221584	sensecap_solar: fix LED definitions (white=11, blue=12)	4 months ago
Quency-D	7a8370fa69	Fixed a bug in the LORA_TX_POWER comment.	3 months ago
Quency-D	cdca79540f	Update Heltec Tracker v2 to version KCT8103L.	3 months ago
João Brázio	9a95e25ef2	Remove unused RX boosted gain mode functions and related preprocessor directives across multiple variants	3 months ago
Quency-D	241805e8c1	Fixed the compilation error of HeltecV4Board::begin.	3 months ago
Wessel Nieboer	67d22401b1	Pass rtc_clock to all MicroNMEALocationProvider instances Enable GPS time synchronization across all variants by passing &rtc_clock to MicroNMEALocationProvider. When GPS gets a valid fix, the RTC clock is now updated automatically every 30 minutes. Updated 16 variants: rak4631, lilygo_tbeam_SX1262, rak_wismesh_tag, lilygo_tbeam_supreme_SX1262, thinknode_m3, heltec_v4, thinknode_m1, lilygo_tbeam_SX1276, meshadventurer, nano_g2_ultra, heltec_v3, promicro, xiao_c3, heltec_tracker_v2, keepteen_lt1, heltec_mesh_solar.	5 months ago
Wessel Nieboer	c0c9c17cf5	and buildscript	3 months ago
Wessel Nieboer	780720c117	and board!	3 months ago
Wessel Nieboer	90fcd1043f	Fix ikoka handheld build The extends was wrong.	3 months ago

1 2 3 4 5 ...

988 Commits (16cb6d518f7639d755cf4aea22d7f741b25ff81f)