Merge adb93565e0 into 6e39cff8a1

variants/thinknode_m3/ThinkNodeM3Board.cpp

@@ -13,6 +13,42 @@ void ThinkNodeM3Board::begin() {
   delay(10);   // give sx1262 some time to power up
 }
 
+void ThinkNodeM3Board::shutdownPeripherals() {
+  NRF52Board::shutdownPeripherals();   // display, LoRa radio and GNSS receiver
+
+  // GPIO output latches survive SYSTEMOFF, so every switched rail still enabled
+  // here keeps draining the battery while the board looks powered off
+  digitalWrite(PIN_GPS_POWER, !GPS_POWER_ACTIVE);
+  digitalWrite(LED_POWER, LOW);     // RGB led supply
+  digitalWrite(EEPROM_POWER, LOW);
+  digitalWrite(BAT_POWER, LOW);     // battery voltage divider
+  digitalWrite(PIN_EN1, LOW);
+  digitalWrite(PIN_EN2, LOW);
+  digitalWrite(PIN_PWR_EN, LOW);
+}
+
+void ThinkNodeM3Board::powerOff() {
+  // turn off all leds, sd_power_system_off will not do this for us
+  digitalWrite(PIN_LED_BLUE, !LED_STATE_ON);
+  digitalWrite(PIN_LED_GREEN, !LED_STATE_ON);
+  digitalWrite(PIN_LED_RED, !LED_STATE_ON);
+
+  // the button is what powers the board back on, and SENSE is level triggered:
+  // wait for the release, or the board wakes up as soon as it goes SYSTEMOFF
+  uint32_t started_at = millis();
+  while (digitalRead(BUTTON_PIN) == LOW) {
+    if (millis() - started_at > 10000) {   // button held down for too long, or stuck:
+      reboot();                            // SYSTEMOFF would wake up right away anyway
+    }
+    delay(10);
+  }
+  delay(50);   // debounce the release
+  nrf_gpio_cfg_sense_input(g_ADigitalPinMap[BUTTON_PIN], NRF_GPIO_PIN_PULLUP, NRF_GPIO_PIN_SENSE_LOW);
+
+  // power off board
+  NRF52Board::powerOff();
+}
+
 uint16_t ThinkNodeM3Board::getBattMilliVolts() {
   int adcvalue = 0;
 

variants/thinknode_m3/ThinkNodeM3Board.h

@@ -42,13 +42,6 @@ public:
     return 0;
   }
 
-  void powerOff() override {
+  void shutdownPeripherals() override;
-    // turn off all leds, sd_power_system_off will not do this for us
+  void powerOff() override;
-    digitalWrite(PIN_LED_BLUE, !LED_STATE_ON);
-    digitalWrite(PIN_LED_GREEN, !LED_STATE_ON);
-    digitalWrite(PIN_LED_RED, !LED_STATE_ON);
-
-    // power off board
-    NRF52Board::powerOff();
-  }
 };

variants/thinknode_m3/variant.cpp

@@ -71,10 +71,10 @@ void initVariant()
   pinMode(EEPROM_POWER, OUTPUT);
   digitalWrite(EEPROM_POWER, HIGH);
 
-  pinMode(36, OUTPUT);
+  pinMode(PIN_EN1, OUTPUT);
-  digitalWrite(36, HIGH);
+  digitalWrite(PIN_EN1, HIGH);
-  pinMode(34, OUTPUT);
+  pinMode(PIN_EN2, OUTPUT);
-  digitalWrite(34, HIGH);
+  digitalWrite(PIN_EN2, HIGH);
 
   pinMode(LED_POWER, OUTPUT);
   digitalWrite(LED_POWER, HIGH);

variants/thinknode_m3/variant.h

@@ -42,6 +42,8 @@
 #define EEPROM_POWER            (7)
 #define BAT_POWER               (17)
 #define PIN_PWR_EN              (16)
+#define PIN_EN1                 (36)            // P1.4, buzzer supply
+#define PIN_EN2                 (34)            // P1.2
 
 
 ////////////////////////////////////////////////////////////////////////////////