Merge pull request #1507 from recrof/rak3401-board-fix

fix: build errors because of changes in RAK3401Board base class

variants/rak3401/RAK3401Board.h

@@ -4,30 +4,6 @@
 #include <Arduino.h>
 #include <helpers/NRF52Board.h>
 
-// LoRa radio module pins for RAK13302
-#define  P_LORA_SCLK    3
-#define  P_LORA_MISO    29
-#define  P_LORA_MOSI    30
-#define  P_LORA_NSS     26
-#define  P_LORA_DIO_1   10
-#define  P_LORA_BUSY    9
-#define  P_LORA_RESET   4
-#ifndef  P_LORA_PA_EN
-  #define  P_LORA_PA_EN  31
-#endif
-
-//#define PIN_GPS_SDA       13  //GPS SDA pin (output option)
-//#define PIN_GPS_SCL       14  //GPS SCL pin (output option)
-// #define PIN_GPS_TX        16  //GPS TX pin
-// #define PIN_GPS_RX        15  //GPS RX pin
-#define PIN_GPS_1PPS      17  //GPS PPS pin
-#define GPS_BAUD_RATE   9600
-#define GPS_ADDRESS   0x42  //i2c address for GPS
-
-#define SX126X_DIO2_AS_RF_SWITCH
-#define SX126X_DIO3_TCXO_VOLTAGE   1.8
-
-
 // built-ins
 #define  PIN_VBAT_READ    5
 #define  ADC_MULTIPLIER   (3 * 1.73 * 1.187 * 1000)
@@ -35,9 +11,13 @@
 #define PIN_3V3_EN (34)
 #define WB_IO2 PIN_3V3_EN
 
-class RAK3401Board : public NRF52BoardDCDC, public NRF52BoardOTA {
+class RAK3401Board : public NRF52BoardDCDC {
+protected:
+#ifdef NRF52_POWER_MANAGEMENT
+  void initiateShutdown(uint8_t reason) override;
+#endif
 public:
-  RAK3401Board() : NRF52BoardOTA("RAK3401_OTA") {}
+  RAK3401Board() : NRF52Board("RAK3401_OTA") {}
   void begin();
 
   #define BATTERY_SAMPLES 8

variants/rak3401/variant.h

@@ -141,11 +141,6 @@ static const uint8_t AREF = PIN_AREF;
 #define EXTERNAL_FLASH_DEVICES IS25LP080D
 #define EXTERNAL_FLASH_USE_QSPI
 
-#define P_LORA_SCK PIN_SPI1_SCK
-#define P_LORA_MISO PIN_SPI1_MISO
-#define P_LORA_MOSI PIN_SPI1_MOSI
-#define P_LORA_CS 26
-
 #define USE_SX1262
 #define SX126X_CS (26)
 #define SX126X_DIO1 (10)
@@ -157,6 +152,15 @@ static const uint8_t AREF = PIN_AREF;
 #define SX126X_DIO2_AS_RF_SWITCH
 #define SX126X_DIO3_TCXO_VOLTAGE 1.8
 
+#define P_LORA_SCLK PIN_SPI1_SCK
+#define P_LORA_MISO PIN_SPI1_MISO
+#define P_LORA_MOSI PIN_SPI1_MOSI
+#define P_LORA_NSS SX126X_CS
+#define P_LORA_DIO_1 SX126X_DIO1
+#define P_LORA_BUSY SX126X_BUSY
+#define P_LORA_RESET SX126X_RESET
+#define P_LORA_PA_EN  31
+
 // enables 3.3V periphery like GPS or IO Module
 // Do not toggle this for GPS power savings
 #define PIN_3V3_EN (34)
@@ -173,6 +177,10 @@ static const uint8_t AREF = PIN_AREF;
 #define PIN_GPS_RX PIN_SERIAL1_RX
 #define PIN_GPS_TX PIN_SERIAL1_TX
 
+#define PIN_GPS_1PPS PIN_GPS_PPS
+#define GPS_BAUD_RATE 9600
+#define GPS_ADDRESS 0x42  //i2c address for GPS
+
 // Battery
 // The battery sense is hooked to pin A0 (5)
 #define BATTERY_PIN PIN_A0