|
|
|
@ -38,6 +38,27 @@ extern "C" |
|
|
|
{ |
|
|
|
#endif // __cplusplus
|
|
|
|
|
|
|
|
/*
|
|
|
|
* WisBlock Base GPIO definitions |
|
|
|
*/ |
|
|
|
static const uint8_t WB_IO1 = 17; // SLOT_A P.12 / SLOT_B P.10
|
|
|
|
static const uint8_t WB_IO2 = 34; // SLOT_A P.10 / SLOT_B P.12
|
|
|
|
static const uint8_t WB_IO3 = 21; // SLOT_C P.12
|
|
|
|
static const uint8_t WB_IO4 = 4; // SLOT_C P.10
|
|
|
|
static const uint8_t WB_IO5 = 9; // SLOT_D P.12
|
|
|
|
static const uint8_t WB_IO6 = 10; // SLOT_D P.10
|
|
|
|
static const uint8_t WB_SW1 = 33; // IO_SLOT
|
|
|
|
static const uint8_t WB_A0 = 5; // IO_SLOT
|
|
|
|
static const uint8_t WB_A1 = 31; // IO_SLOT
|
|
|
|
static const uint8_t WB_I2C1_SDA = 13; // SENSOR_SLOT IO_SLOT
|
|
|
|
static const uint8_t WB_I2C1_SCL = 14; // SENSOR_SLOT IO_SLOT
|
|
|
|
static const uint8_t WB_I2C2_SDA = 24; // IO_SLOT
|
|
|
|
static const uint8_t WB_I2C2_SCL = 25; // IO_SLOT
|
|
|
|
static const uint8_t WB_SPI_CS = 26; // IO_SLOT
|
|
|
|
static const uint8_t WB_SPI_CLK = 3; // IO_SLOT
|
|
|
|
static const uint8_t WB_SPI_MISO = 29; // IO_SLOT
|
|
|
|
static const uint8_t WB_SPI_MOSI = 30; // IO_SLOT
|
|
|
|
|
|
|
|
// Number of pins defined in PinDescription array
|
|
|
|
#define PINS_COUNT (48) |
|
|
|
#define NUM_DIGITAL_PINS (48) |
|
|
|
@ -92,8 +113,6 @@ extern "C" |
|
|
|
|
|
|
|
#define PIN_AREF (2) |
|
|
|
#define PIN_NFC1 (9) |
|
|
|
#define WB_IO5 PIN_NFC1 |
|
|
|
#define WB_IO4 (4) |
|
|
|
#define PIN_NFC2 (10) |
|
|
|
|
|
|
|
static const uint8_t AREF = PIN_AREF; |
|
|
|
@ -178,20 +197,10 @@ static const uint8_t AREF = PIN_AREF; |
|
|
|
// enables 3.3V periphery like GPS or IO Module
|
|
|
|
// Do not toggle this for GPS power savings
|
|
|
|
#define PIN_3V3_EN (34) |
|
|
|
#define WB_IO2 PIN_3V3_EN |
|
|
|
|
|
|
|
// RAK1910 GPS module
|
|
|
|
// If using the wisblock GPS module and pluged into Port A on WisBlock base
|
|
|
|
// IO1 is hooked to PPS (pin 12 on header) = gpio 17
|
|
|
|
// IO2 is hooked to GPS RESET = gpio 34, but it can not be used to this because IO2 is ALSO used to control 3V3_S power (1 is on).
|
|
|
|
// Therefore must be 1 to keep peripherals powered
|
|
|
|
// Power is on the controllable 3V3_S rail
|
|
|
|
#define PIN_GPS_PPS (17) // Pulse per second input from the GPS
|
|
|
|
|
|
|
|
#define PIN_GPS_RX PIN_SERIAL1_RX |
|
|
|
#define PIN_GPS_TX PIN_SERIAL1_TX |
|
|
|
|
|
|
|
#define PIN_GPS_1PPS PIN_GPS_PPS |
|
|
|
#define GPS_BAUD_RATE 9600 |
|
|
|
#define GPS_ADDRESS 0x42 //i2c address for GPS
|
|
|
|
|
|
|
|
|
Yoshi Walsh
11 hours ago