mirror of https://github.com/meshcore-dev/MeshCore
Browse Source
There is a lot to this PR, so if there are any questions let me know. The idea here is to merge T-Beam fw so that there is less redundant code. Most versions (except the 0.7) share PMU code, init sequence, and most IO pin definitions. - Merged all T-Beam board.h files into one TBeamBoard. - Added PMU code to identify different AXP chips. - Modified "lilygo tbeam SX1276" variant to cover all T-Beam SX1276 versions - Modified "lilygo tbeam SX1262" variant to cover all T-Beam SX1262 versions - Enabled GPS on all T-Beam versions/models - Enabled BME280 on the Supreme I am also updating EnvironmentSensorManager to allow for boards that do or don't have GPS enable pins, as well as a PERSISTANT_GPS define check for boards that want GPS to stay active after boot.pull/439/head
cod3doomy
12 months ago
15 changed files with 773 additions and 718 deletions
@ -1,87 +0,0 @@ |
|||||
#pragma once |
|
||||
|
|
||||
|
|
||||
#include <Wire.h> |
|
||||
#include <Arduino.h> |
|
||||
#include "XPowersLib.h" |
|
||||
|
|
||||
// Defined using AXP2102
|
|
||||
#define XPOWERS_CHIP_AXP2101 |
|
||||
#define PIN_BOARD_SDA1 42 //SDA for PMU and PFC8563 (RTC)
|
|
||||
#define PIN_BOARD_SCL1 41 //SCL for PMU and PFC8563 (RTC)
|
|
||||
#define PIN_PMU_IRQ 40 //IRQ pin for PMU
|
|
||||
|
|
||||
// LoRa radio module pins for TBeam
|
|
||||
#define P_LORA_DIO_0 26 |
|
||||
#define P_LORA_DIO_2 32 |
|
||||
#define P_LORA_DIO_1 33 |
|
||||
#define P_LORA_NSS 18 |
|
||||
#define P_LORA_RESET 14 |
|
||||
#define P_LORA_BUSY RADIOLIB_NC |
|
||||
#define P_LORA_SCLK 5 |
|
||||
#define P_LORA_MISO 19 |
|
||||
#define P_LORA_MOSI 27 |
|
||||
|
|
||||
// built-ins
|
|
||||
//#define PIN_VBAT_READ 37
|
|
||||
//#define PIN_LED_BUILTIN 25
|
|
||||
|
|
||||
#include "ESP32Board.h" |
|
||||
|
|
||||
#include <driver/rtc_io.h> |
|
||||
|
|
||||
class TBeamBoard : public ESP32Board { |
|
||||
XPowersLibInterface *PMU = NULL; |
|
||||
public: |
|
||||
bool power_init(); |
|
||||
void printPMU(); |
|
||||
|
|
||||
void begin() { |
|
||||
ESP32Board::begin(); |
|
||||
pinMode(38, INPUT_PULLUP); |
|
||||
|
|
||||
esp_reset_reason_t reason = esp_reset_reason(); |
|
||||
if (reason == ESP_RST_DEEPSLEEP) { |
|
||||
long wakeup_source = esp_sleep_get_ext1_wakeup_status(); |
|
||||
if (wakeup_source & (1 << P_LORA_DIO_1)) { // received a LoRa packet (while in deep sleep)
|
|
||||
startup_reason = BD_STARTUP_RX_PACKET; |
|
||||
} |
|
||||
|
|
||||
rtc_gpio_hold_dis((gpio_num_t)P_LORA_NSS); |
|
||||
rtc_gpio_deinit((gpio_num_t)P_LORA_DIO_1); |
|
||||
} |
|
||||
power_init(); |
|
||||
} |
|
||||
|
|
||||
void enterDeepSleep(uint32_t secs, int pin_wake_btn = -1) { |
|
||||
esp_sleep_pd_config(ESP_PD_DOMAIN_RTC_PERIPH, ESP_PD_OPTION_ON); |
|
||||
|
|
||||
// Make sure the DIO1 and NSS GPIOs are hold on required levels during deep sleep
|
|
||||
rtc_gpio_set_direction((gpio_num_t)P_LORA_DIO_1, RTC_GPIO_MODE_INPUT_ONLY); |
|
||||
rtc_gpio_pulldown_en((gpio_num_t)P_LORA_DIO_1); |
|
||||
|
|
||||
rtc_gpio_hold_en((gpio_num_t)P_LORA_NSS); |
|
||||
|
|
||||
if (pin_wake_btn < 0) { |
|
||||
esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet
|
|
||||
} else { |
|
||||
esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1) | (1L << pin_wake_btn), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet OR wake btn
|
|
||||
} |
|
||||
|
|
||||
if (secs > 0) { |
|
||||
esp_sleep_enable_timer_wakeup(secs * 1000000); |
|
||||
} |
|
||||
|
|
||||
// Finally set ESP32 into sleep
|
|
||||
esp_deep_sleep_start(); // CPU halts here and never returns!
|
|
||||
} |
|
||||
|
|
||||
uint16_t getBattMilliVolts() override { |
|
||||
if(PMU) return PMU->getBattVoltage(); |
|
||||
else return 0; |
|
||||
} |
|
||||
|
|
||||
const char* getManufacturerName() const override { |
|
||||
return "LilyGo T-Beam"; |
|
||||
} |
|
||||
}; |
|
||||
@ -1,79 +0,0 @@ |
|||||
#pragma once |
|
||||
|
|
||||
|
|
||||
#include <Wire.h> |
|
||||
#include <Arduino.h> |
|
||||
#include "XPowersLib.h" |
|
||||
|
|
||||
#define XPOWERS_CHIP_AXP192 |
|
||||
|
|
||||
// LoRa radio module pins for TBeam
|
|
||||
#define P_LORA_DIO_1 33 // SX1262 IRQ pin
|
|
||||
#define P_LORA_NSS 18 |
|
||||
#define P_LORA_RESET 23 |
|
||||
#define P_LORA_BUSY 32 // SX1262 Busy pin
|
|
||||
#define P_LORA_SCLK 5 |
|
||||
#define P_LORA_MISO 19 |
|
||||
#define P_LORA_MOSI 27 |
|
||||
|
|
||||
#include "ESP32Board.h" |
|
||||
|
|
||||
#include <driver/rtc_io.h> |
|
||||
|
|
||||
class TBeamBoardSX1262 : public ESP32Board { |
|
||||
XPowersAXP192 power; |
|
||||
|
|
||||
public: |
|
||||
void begin() { |
|
||||
ESP32Board::begin(); |
|
||||
|
|
||||
power.setLDO2Voltage(3300); |
|
||||
power.enableLDO2(); |
|
||||
|
|
||||
power.enableBattVoltageMeasure(); |
|
||||
|
|
||||
pinMode(38, INPUT_PULLUP); |
|
||||
|
|
||||
esp_reset_reason_t reason = esp_reset_reason(); |
|
||||
if (reason == ESP_RST_DEEPSLEEP) { |
|
||||
long wakeup_source = esp_sleep_get_ext1_wakeup_status(); |
|
||||
if (wakeup_source & (1 << P_LORA_DIO_1)) { // received a LoRa packet (while in deep sleep)
|
|
||||
startup_reason = BD_STARTUP_RX_PACKET; |
|
||||
} |
|
||||
|
|
||||
rtc_gpio_hold_dis((gpio_num_t)P_LORA_NSS); |
|
||||
rtc_gpio_deinit((gpio_num_t)P_LORA_DIO_1); |
|
||||
} |
|
||||
} |
|
||||
|
|
||||
void enterDeepSleep(uint32_t secs, int pin_wake_btn = -1) { |
|
||||
esp_sleep_pd_config(ESP_PD_DOMAIN_RTC_PERIPH, ESP_PD_OPTION_ON); |
|
||||
|
|
||||
// Make sure the DIO1 and NSS GPIOs are hold on required levels during deep sleep
|
|
||||
rtc_gpio_set_direction((gpio_num_t)P_LORA_DIO_1, RTC_GPIO_MODE_INPUT_ONLY); |
|
||||
rtc_gpio_pulldown_en((gpio_num_t)P_LORA_DIO_1); |
|
||||
|
|
||||
rtc_gpio_hold_en((gpio_num_t)P_LORA_NSS); |
|
||||
|
|
||||
if (pin_wake_btn < 0) { |
|
||||
esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet
|
|
||||
} else { |
|
||||
esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1) | (1L << pin_wake_btn), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet OR wake btn
|
|
||||
} |
|
||||
|
|
||||
if (secs > 0) { |
|
||||
esp_sleep_enable_timer_wakeup(secs * 1000000); |
|
||||
} |
|
||||
|
|
||||
// Finally set ESP32 into sleep
|
|
||||
esp_deep_sleep_start(); // CPU halts here and never returns!
|
|
||||
} |
|
||||
|
|
||||
uint16_t getBattMilliVolts() override { |
|
||||
return power.getBattVoltage(); |
|
||||
} |
|
||||
|
|
||||
const char* getManufacturerName() const override { |
|
||||
return "LilyGo T-Beam SX1262"; |
|
||||
} |
|
||||
}; |
|
||||
@ -1,116 +0,0 @@ |
|||||
#pragma once |
|
||||
|
|
||||
#include "ESP32Board.h" |
|
||||
#include <driver/rtc_io.h> |
|
||||
#include <Wire.h> |
|
||||
#include <Arduino.h> |
|
||||
#include "XPowersLib.h" |
|
||||
|
|
||||
// LoRa radio module pins for TBeam S3 Supreme
|
|
||||
#define P_LORA_DIO_1 1 //SX1262 IRQ pin
|
|
||||
#define P_LORA_NSS 10 //SX1262 SS pin
|
|
||||
#define P_LORA_RESET 5 //SX1262 Rest pin
|
|
||||
#define P_LORA_BUSY 4 //SX1262 Busy pin
|
|
||||
#define P_LORA_SCLK 12 //SX1262 SCLK pin
|
|
||||
#define P_LORA_MISO 13 //SX1262 MISO pin
|
|
||||
#define P_LORA_MOSI 11 //SX1262 MOSI pin
|
|
||||
|
|
||||
//#define PIN_BOARD_SDA 17 //SDA for OLED, BME280, and QMC6310U (0x1C)
|
|
||||
//#define PIN_BOARD_SCL 18 //SCL for OLED, BME280, and QMC6310U (0x1C)
|
|
||||
|
|
||||
#define PIN_BOARD_SDA1 42 //SDA for PMU and PFC8563 (RTC)
|
|
||||
#define PIN_BOARD_SCL1 41 //SCL for PMU and PFC8563 (RTC)
|
|
||||
#define PIN_PMU_IRQ 40 //IRQ pin for PMU
|
|
||||
|
|
||||
//#define PIN_USER_BTN 0
|
|
||||
|
|
||||
#define P_BOARD_SPI_MOSI 35 //SPI for SD Card and QMI8653 (IMU)
|
|
||||
#define P_BOARD_SPI_MISO 37 //SPI for SD Card and QMI8653 (IMU)
|
|
||||
#define P_BOARD_SPI_SCK 36 //SPI for SD Card and QMI8653 (IMU)
|
|
||||
#define P_BPARD_SPI_CS 47 //Pin for SD Card CS
|
|
||||
#define P_BOARD_IMU_CS 34 //Pin for QMI8653 (IMU) CS
|
|
||||
|
|
||||
#define P_BOARD_IMU_INT 33 //IMU Int pin
|
|
||||
#define P_BOARD_RTC_INT 14 //RTC Int pin
|
|
||||
|
|
||||
#define P_GPS_RX 9 //GPS RX pin
|
|
||||
#define P_GPS_TX 8 //GPS TX pin
|
|
||||
#define P_GPS_WAKE 7 //GPS Wakeup pin
|
|
||||
//#define P_GPS_1PPS 6 //GPS 1PPS pin - repurposed for lora tx led
|
|
||||
#define GPS_BAUD_RATE 9600 |
|
||||
|
|
||||
//I2C Wire addresses
|
|
||||
#define I2C_BME280_ADD 0x76 //BME280 sensor I2C address on Wire
|
|
||||
#define I2C_OLED_ADD 0x3C //SH1106 OLED I2C address on Wire
|
|
||||
#define I2C_QMC6310U_ADD 0x1C //QMC6310U mag sensor I2C address on Wire
|
|
||||
|
|
||||
//I2C Wire1 addresses
|
|
||||
#define I2C_RTC_ADD 0x51 //RTC I2C address on Wire1
|
|
||||
#define I2C_PMU_ADD 0x34 //AXP2101 I2C address on Wire1
|
|
||||
|
|
||||
#define PMU_WIRE_PORT Wire1 |
|
||||
#define XPOWERS_CHIP_AXP2101 |
|
||||
|
|
||||
class TBeamS3SupremeBoard : public ESP32Board { |
|
||||
XPowersAXP2101 PMU; |
|
||||
public: |
|
||||
#ifdef MESH_DEBUG |
|
||||
void printPMU(); |
|
||||
#endif |
|
||||
bool power_init(); |
|
||||
|
|
||||
void begin() { |
|
||||
|
|
||||
ESP32Board::begin(); |
|
||||
|
|
||||
power_init(); |
|
||||
|
|
||||
esp_reset_reason_t reason = esp_reset_reason(); |
|
||||
if (reason == ESP_RST_DEEPSLEEP) { |
|
||||
long wakeup_source = esp_sleep_get_ext1_wakeup_status(); |
|
||||
if (wakeup_source & (1 << P_LORA_DIO_1)) { // received a LoRa packet (while in deep sleep)
|
|
||||
startup_reason = BD_STARTUP_RX_PACKET; |
|
||||
} |
|
||||
|
|
||||
rtc_gpio_hold_dis((gpio_num_t)P_LORA_NSS); |
|
||||
rtc_gpio_deinit((gpio_num_t)P_LORA_DIO_1); |
|
||||
} |
|
||||
power_init(); |
|
||||
} |
|
||||
|
|
||||
void enterDeepSleep(uint32_t secs, int pin_wake_btn = -1) { |
|
||||
esp_sleep_pd_config(ESP_PD_DOMAIN_RTC_PERIPH, ESP_PD_OPTION_ON); |
|
||||
|
|
||||
// Make sure the DIO1 and NSS GPIOs are hold on required levels during deep sleep
|
|
||||
rtc_gpio_set_direction((gpio_num_t)P_LORA_DIO_1, RTC_GPIO_MODE_INPUT_ONLY); |
|
||||
rtc_gpio_pulldown_en((gpio_num_t)P_LORA_DIO_1); |
|
||||
|
|
||||
rtc_gpio_hold_en((gpio_num_t)P_LORA_NSS); |
|
||||
|
|
||||
if (pin_wake_btn < 0) { |
|
||||
esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet
|
|
||||
} else { |
|
||||
esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1) | (1L << pin_wake_btn), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet OR wake btn
|
|
||||
} |
|
||||
|
|
||||
if (secs > 0) { |
|
||||
esp_sleep_enable_timer_wakeup(secs * 1000000); |
|
||||
} |
|
||||
|
|
||||
// Finally set ESP32 into sleep
|
|
||||
esp_deep_sleep_start(); // CPU halts here and never returns!
|
|
||||
} |
|
||||
|
|
||||
uint16_t getBattMilliVolts() override { |
|
||||
return PMU.getBattVoltage(); |
|
||||
} |
|
||||
|
|
||||
uint16_t getBattPercent() { |
|
||||
//Read the PMU fuel guage for battery %
|
|
||||
uint16_t battPercent = PMU.getBatteryPercent(); |
|
||||
return battPercent; |
|
||||
} |
|
||||
const char* getManufacturerName() const override { |
|
||||
return "LilyGo T-Beam S3 Supreme SX1262"; |
|
||||
} |
|
||||
}; |
|
||||
@ -0,0 +1,346 @@ |
|||||
|
#include <Arduino.h> |
||||
|
#include "TBeamBoard.h" |
||||
|
//#include <RadioLib.h>
|
||||
|
|
||||
|
uint32_t deviceOnline = 0x00; |
||||
|
|
||||
|
bool pmuInterrupt; |
||||
|
static void setPmuFlag() |
||||
|
{ |
||||
|
pmuInterrupt = true; |
||||
|
} |
||||
|
|
||||
|
void TBeamBoard::begin() { |
||||
|
|
||||
|
ESP32Board::begin(); |
||||
|
|
||||
|
power_init(); |
||||
|
|
||||
|
//Configure user button
|
||||
|
pinMode(PIN_USER_BTN, INPUT); |
||||
|
|
||||
|
#ifndef TBEAM_SUPREME_SX1262 |
||||
|
digitalWrite(P_LORA_TX_LED, HIGH); //inverted pin for SX1276 - HIGH for off
|
||||
|
#endif |
||||
|
|
||||
|
//radiotype_detect();
|
||||
|
|
||||
|
esp_reset_reason_t reason = esp_reset_reason(); |
||||
|
if (reason == ESP_RST_DEEPSLEEP) { |
||||
|
long wakeup_source = esp_sleep_get_ext1_wakeup_status(); |
||||
|
if (wakeup_source & (1 << P_LORA_DIO_1)) { // received a LoRa packet (while in deep sleep)
|
||||
|
startup_reason = BD_STARTUP_RX_PACKET; |
||||
|
} |
||||
|
|
||||
|
rtc_gpio_hold_dis((gpio_num_t)P_LORA_NSS); |
||||
|
rtc_gpio_deinit((gpio_num_t)P_LORA_DIO_1); |
||||
|
} |
||||
|
} |
||||
|
|
||||
|
#ifdef MESH_DEBUG |
||||
|
void TBeamBoard::scanDevices(TwoWire *w) |
||||
|
{ |
||||
|
uint8_t err, addr; |
||||
|
int nDevices = 0; |
||||
|
uint32_t start = 0; |
||||
|
|
||||
|
Serial.println("Scanning I2C for Devices"); |
||||
|
for (addr = 1; addr < 127; addr++) { |
||||
|
start = millis(); |
||||
|
w->beginTransmission(addr); delay(2); |
||||
|
err = w->endTransmission(); |
||||
|
if (err == 0) { |
||||
|
nDevices++; |
||||
|
switch (addr) { |
||||
|
case 0x77: |
||||
|
case 0x76: |
||||
|
Serial.println("\tFound BME280 Sensor"); |
||||
|
deviceOnline |= BME280_ONLINE; |
||||
|
break; |
||||
|
case 0x34: |
||||
|
Serial.println("\tFound AXP192/AXP2101 PMU"); |
||||
|
deviceOnline |= POWERMANAGE_ONLINE; |
||||
|
break; |
||||
|
case 0x3C: |
||||
|
Serial.println("\tFound SSD1306/SH1106 display"); |
||||
|
deviceOnline |= DISPLAY_ONLINE; |
||||
|
break; |
||||
|
case 0x51: |
||||
|
Serial.println("\tFound PCF8563 RTC"); |
||||
|
deviceOnline |= PCF8563_ONLINE; |
||||
|
break; |
||||
|
case 0x1C: |
||||
|
Serial.println("\tFound QMC6310 MAG Sensor"); |
||||
|
deviceOnline |= QMC6310_ONLINE; |
||||
|
break; |
||||
|
default: |
||||
|
Serial.print("\tI2C device found at address 0x"); |
||||
|
if (addr < 16) { |
||||
|
Serial.print("0"); |
||||
|
} |
||||
|
Serial.print(addr, HEX); |
||||
|
Serial.println(" !"); |
||||
|
break; |
||||
|
} |
||||
|
|
||||
|
} else if (err == 4) { |
||||
|
Serial.print("Unknow error at address 0x"); |
||||
|
if (addr < 16) { |
||||
|
Serial.print("0"); |
||||
|
} |
||||
|
Serial.println(addr, HEX); |
||||
|
} |
||||
|
} |
||||
|
if (nDevices == 0) |
||||
|
Serial.println("No I2C devices found\n"); |
||||
|
|
||||
|
Serial.println("Scan for devices is complete."); |
||||
|
Serial.println("\n"); |
||||
|
|
||||
|
Serial.printf("GPS RX pin: %d", PIN_GPS_RX); |
||||
|
Serial.printf(" GPS TX pin: %d", PIN_GPS_TX); |
||||
|
Serial.println(); |
||||
|
} |
||||
|
void TBeamBoard::printPMU() |
||||
|
{ |
||||
|
Serial.print("isCharging:"); Serial.println(PMU->isCharging() ? "YES" : "NO"); |
||||
|
Serial.print("isDischarge:"); Serial.println(PMU->isDischarge() ? "YES" : "NO"); |
||||
|
Serial.print("isVbusIn:"); Serial.println(PMU->isVbusIn() ? "YES" : "NO"); |
||||
|
Serial.print("getBattVoltage:"); Serial.print(PMU->getBattVoltage()); Serial.println("mV"); |
||||
|
Serial.print("getVbusVoltage:"); Serial.print(PMU->getVbusVoltage()); Serial.println("mV"); |
||||
|
Serial.print("getSystemVoltage:"); Serial.print(PMU->getSystemVoltage()); Serial.println("mV"); |
||||
|
|
||||
|
// The battery percentage may be inaccurate at first use, the PMU will automatically
|
||||
|
// learn the battery curve and will automatically calibrate the battery percentage
|
||||
|
// after a charge and discharge cycle
|
||||
|
if (PMU->isBatteryConnect()) { |
||||
|
Serial.print("getBatteryPercent:"); Serial.print(PMU->getBatteryPercent()); Serial.println("%"); |
||||
|
} |
||||
|
|
||||
|
Serial.println(); |
||||
|
} |
||||
|
#endif |
||||
|
|
||||
|
bool TBeamBoard::power_init() |
||||
|
{ |
||||
|
if (!PMU) { |
||||
|
#ifdef TBEAM_SUPREME_SX1262 |
||||
|
PMU = new XPowersAXP2101(PMU_WIRE_PORT, PIN_BOARD_SDA1, PIN_BOARD_SCL1, I2C_PMU_ADD); |
||||
|
#else |
||||
|
PMU = new XPowersAXP2101(PMU_WIRE_PORT, PIN_BOARD_SDA, PIN_BOARD_SCL, I2C_PMU_ADD); |
||||
|
#endif |
||||
|
if (!PMU->init()) { |
||||
|
MESH_DEBUG_PRINTLN("Warning: Failed to find AXP2101 power management"); |
||||
|
delete PMU; |
||||
|
PMU = NULL; |
||||
|
} else { |
||||
|
MESH_DEBUG_PRINTLN("AXP2101 PMU init succeeded, using AXP2101 PMU"); |
||||
|
} |
||||
|
} |
||||
|
if (!PMU) { |
||||
|
PMU = new XPowersAXP192(PMU_WIRE_PORT, PIN_BOARD_SDA, PIN_BOARD_SCL, I2C_PMU_ADD); |
||||
|
if (!PMU->init()) { |
||||
|
MESH_DEBUG_PRINTLN("Warning: Failed to find AXP192 power management"); |
||||
|
delete PMU; |
||||
|
PMU = NULL; |
||||
|
} else { |
||||
|
MESH_DEBUG_PRINTLN("AXP192 PMU init succeeded, using AXP192 PMU"); |
||||
|
} |
||||
|
} |
||||
|
|
||||
|
if (!PMU) { |
||||
|
return false; |
||||
|
} |
||||
|
|
||||
|
deviceOnline |= POWERMANAGE_ONLINE; |
||||
|
|
||||
|
PMU->setChargingLedMode(XPOWERS_CHG_LED_CTRL_CHG); |
||||
|
|
||||
|
// Set up PMU interrupts
|
||||
|
pinMode(PIN_PMU_IRQ, INPUT_PULLUP); |
||||
|
attachInterrupt(PIN_PMU_IRQ, setPmuFlag, FALLING); |
||||
|
|
||||
|
if (PMU->getChipModel() == XPOWERS_AXP192) { |
||||
|
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_LDO2, 3300); //Set up LoRa power rail
|
||||
|
PMU->enablePowerOutput(XPOWERS_LDO2); //Enable the LoRa power rail
|
||||
|
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_DCDC1, 3300); //Set up OLED power rail
|
||||
|
PMU->enablePowerOutput(XPOWERS_DCDC1); //Enable the OLED power rail
|
||||
|
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_LDO3, 3300); //Set up GPS power rail
|
||||
|
PMU->enablePowerOutput(XPOWERS_LDO3); //Enable the GPS power rail
|
||||
|
|
||||
|
PMU->setProtectedChannel(XPOWERS_DCDC1); //Protect the OLED power rail
|
||||
|
PMU->setProtectedChannel(XPOWERS_DCDC3); //Protect the ESP32 power rail
|
||||
|
|
||||
|
PMU->disablePowerOutput(XPOWERS_DCDC2); //Disable unsused power rail DC2
|
||||
|
|
||||
|
PMU->disableIRQ(XPOWERS_AXP192_ALL_IRQ); //Disable PMU IRQ
|
||||
|
|
||||
|
PMU->setChargerConstantCurr(XPOWERS_AXP192_CHG_CUR_450MA); //Set battery charging current
|
||||
|
PMU->setChargeTargetVoltage(XPOWERS_AXP192_CHG_VOL_4V2); //Set battery charge-stop voltage
|
||||
|
} |
||||
|
else if(PMU->getChipModel() == XPOWERS_AXP2101){ |
||||
|
#ifdef TBEAM_SUPREME_SX1262 |
||||
|
//Set up the GPS power rail
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_ALDO4, 3300); |
||||
|
PMU->enablePowerOutput(XPOWERS_ALDO4); |
||||
|
|
||||
|
//Set up the LoRa power rail
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_ALDO3, 3300); |
||||
|
PMU->enablePowerOutput(XPOWERS_ALDO3); |
||||
|
|
||||
|
//Set up power rail for the M.2 interface
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_DCDC3, 3300); |
||||
|
PMU->enablePowerOutput(XPOWERS_DCDC3); |
||||
|
|
||||
|
if (ESP_SLEEP_WAKEUP_UNDEFINED == esp_sleep_get_wakeup_cause()) { |
||||
|
MESH_DEBUG_PRINTLN("Power off and restart ALDO BLDO.."); |
||||
|
PMU->disablePowerOutput(XPOWERS_ALDO1); |
||||
|
PMU->disablePowerOutput(XPOWERS_ALDO2); |
||||
|
PMU->disablePowerOutput(XPOWERS_BLDO1); |
||||
|
delay(250); |
||||
|
} |
||||
|
|
||||
|
//Set up power rail for QMC6310U
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_ALDO2, 3300); |
||||
|
PMU->enablePowerOutput(XPOWERS_ALDO2); |
||||
|
|
||||
|
//Set up power rail for BME280 and OLED
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_ALDO1, 3300); |
||||
|
PMU->enablePowerOutput(XPOWERS_ALDO1); |
||||
|
|
||||
|
//Set up pwer rail for SD Card
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_BLDO1, 3300); |
||||
|
PMU->enablePowerOutput(XPOWERS_BLDO1); |
||||
|
|
||||
|
//Set up power rail BLDO2 to headers
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_BLDO2, 3300); |
||||
|
PMU->enablePowerOutput(XPOWERS_BLDO2); |
||||
|
|
||||
|
//Set up power rail DCDC4 to headers
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_DCDC4, XPOWERS_AXP2101_DCDC4_VOL2_MAX); |
||||
|
PMU->enablePowerOutput(XPOWERS_DCDC4); |
||||
|
|
||||
|
//Set up power rail DCDC5 to headers
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_DCDC5, 3300); |
||||
|
PMU->enablePowerOutput(XPOWERS_DCDC5); |
||||
|
|
||||
|
//Disable unused power rails
|
||||
|
PMU->disablePowerOutput(XPOWERS_DCDC2); |
||||
|
PMU->disablePowerOutput(XPOWERS_DLDO1); |
||||
|
PMU->disablePowerOutput(XPOWERS_DLDO2); |
||||
|
PMU->disablePowerOutput(XPOWERS_VBACKUP); |
||||
|
#else |
||||
|
//Turn off unused power rails
|
||||
|
PMU->disablePowerOutput(XPOWERS_DCDC2); |
||||
|
PMU->disablePowerOutput(XPOWERS_DCDC3); |
||||
|
PMU->disablePowerOutput(XPOWERS_DCDC4); |
||||
|
PMU->disablePowerOutput(XPOWERS_DCDC5); |
||||
|
PMU->disablePowerOutput(XPOWERS_ALDO1); |
||||
|
PMU->disablePowerOutput(XPOWERS_ALDO4); |
||||
|
PMU->disablePowerOutput(XPOWERS_BLDO1); |
||||
|
PMU->disablePowerOutput(XPOWERS_BLDO2); |
||||
|
PMU->disablePowerOutput(XPOWERS_DLDO1); |
||||
|
PMU->disablePowerOutput(XPOWERS_DLDO2); |
||||
|
//PMU->disablePowerOutput(XPOWERS_CPULDO);
|
||||
|
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_VBACKUP, 3300); //Set up GPS RTC power
|
||||
|
PMU->enablePowerOutput(XPOWERS_VBACKUP); //Turn on GPS RTC power
|
||||
|
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_ALDO2, 3300); //Set up LoRa power rail
|
||||
|
PMU->enablePowerOutput(XPOWERS_ALDO2); //Enable LoRa power rail
|
||||
|
|
||||
|
PMU->setPowerChannelVoltage(XPOWERS_ALDO3, 3300); //Set up GPS power rail
|
||||
|
PMU->enablePowerOutput(XPOWERS_ALDO3); //Enable GPS power rail
|
||||
|
|
||||
|
#endif |
||||
|
|
||||
|
PMU->disableIRQ(XPOWERS_AXP2101_ALL_IRQ); //Disable all PMU interrupts
|
||||
|
|
||||
|
PMU->setChargerConstantCurr(XPOWERS_AXP2101_CHG_CUR_500MA); //Set battery charging current to 500mA
|
||||
|
PMU->setChargeTargetVoltage(XPOWERS_AXP2101_CHG_VOL_4V2); //Set battery charging cutoff voltage to 4.2V
|
||||
|
|
||||
|
} |
||||
|
|
||||
|
PMU->clearIrqStatus(); //Clear interrupt flags
|
||||
|
|
||||
|
PMU->disableTSPinMeasure(); //Disable TS detection, since it is not used
|
||||
|
|
||||
|
//Enable voltage measurements
|
||||
|
PMU->enableSystemVoltageMeasure(); |
||||
|
PMU->enableVbusVoltageMeasure(); |
||||
|
PMU->enableBattVoltageMeasure(); |
||||
|
|
||||
|
#ifdef MESH_DEBUG |
||||
|
scanDevices(&Wire); |
||||
|
printPMU(); |
||||
|
#endif |
||||
|
|
||||
|
// Set the power key off press time
|
||||
|
PMU->setPowerKeyPressOffTime(XPOWERS_POWEROFF_4S); |
||||
|
return true; |
||||
|
} |
||||
|
|
||||
|
#pragma region "Debug code" |
||||
|
// void TBeamBoard::radiotype_detect(){
|
||||
|
|
||||
|
// static SPIClass spi;
|
||||
|
// char chipTypeInfo;
|
||||
|
|
||||
|
// #if defined(P_LORA_SCLK)
|
||||
|
// spi.begin(P_LORA_SCLK, P_LORA_MISO, P_LORA_MOSI);
|
||||
|
// #endif
|
||||
|
|
||||
|
// for(int i = 0; i<radioVersions; i++){
|
||||
|
// switch(i){
|
||||
|
// case 0:
|
||||
|
// CustomSX1262 radio = new Module(P_LORA_NSS, P_LORA_DIO_0, P_LORA_RESET, P_LORA_DIO_1, spi);
|
||||
|
// int status = radio.begin(LORA_FREQ, LORA_BW, LORA_SF, LORA_CR, RADIOLIB_SX126X_SYNC_WORD_PRIVATE, LORA_TX_POWER, 8);
|
||||
|
// if (status != RADIOLIB_ERR_NONE) {
|
||||
|
// Serial.print("ERROR: SX1262 not found: ");
|
||||
|
// Serial.println(status);
|
||||
|
// //delete radio;
|
||||
|
// radio = NULL;
|
||||
|
// break;
|
||||
|
// }
|
||||
|
// else{
|
||||
|
// MESH_DEBUG_PRINTLN("SX1262 detected");
|
||||
|
// P_LORA_BUSY = 32;
|
||||
|
// RADIO_CLASS = CustomSX1262;
|
||||
|
// WRAPPER_CLASS = CustomSX1262Wrapper;
|
||||
|
// SX126X_RX_BOOSTED_GAIN = true;
|
||||
|
// SX126X_CURRENT_LIMIT = 140;
|
||||
|
// //delete radio;
|
||||
|
// radio = NULL;
|
||||
|
// break;
|
||||
|
// }
|
||||
|
// case 1:
|
||||
|
// SX1276 radio = new Module(P_LORA_NSS, P_LORA_DIO_0, P_LORA_RESET, P_LORA_DIO_1, spi);
|
||||
|
// int status1 = radio.begin(LORA_FREQ, LORA_BW, LORA_SF, LORA_CR, RADIOLIB_SX126X_SYNC_WORD_PRIVATE, LORA_TX_POWER, 8);
|
||||
|
// if (status1 != RADIOLIB_ERR_NONE) {
|
||||
|
// Serial.print("ERROR: SX1272 not found: ");
|
||||
|
// Serial.println(status1);
|
||||
|
// //delete radio;
|
||||
|
// radio = NULL;
|
||||
|
// }
|
||||
|
// else{
|
||||
|
// MESH_DEBUG_PRINTLN("SX1272 detected");
|
||||
|
// P_LORA_BUSY = RADIOLIB_NC;
|
||||
|
// P_LORA_DIO_2 = 32;
|
||||
|
// RADIO_CLASS = CustomSX1272;
|
||||
|
// WRAPPER_CLASS = CustomSX1272Wrapper;
|
||||
|
// SX127X_CURRENT_LIMIT = 120;
|
||||
|
// //delete radio;
|
||||
|
// radio = NULL;
|
||||
|
// return;
|
||||
|
// }
|
||||
|
// default:
|
||||
|
// }
|
||||
|
// }
|
||||
|
|
||||
|
|
||||
|
|
||||
|
// }
|
||||
|
#pragma endregion |
||||
@ -0,0 +1,164 @@ |
|||||
|
#pragma once |
||||
|
|
||||
|
#include <Wire.h> |
||||
|
#include <Arduino.h> |
||||
|
#include "XPowersLib.h" |
||||
|
#include "helpers/ESP32Board.h" |
||||
|
#include <driver/rtc_io.h> |
||||
|
//#include <RadioLib.h>
|
||||
|
//#include <helpers/RadioLibWrappers.h>
|
||||
|
//#include <helpers/CustomSX1262Wrapper.h>
|
||||
|
//#include <helpers/CustomSX1276Wrapper.h>
|
||||
|
|
||||
|
#ifdef TBEAM_SUPREME_SX1262 |
||||
|
// LoRa radio module pins for TBeam S3 Supreme SX1262
|
||||
|
#define P_LORA_DIO_0 -1 //NC
|
||||
|
#define P_LORA_DIO_1 1 //SX1262 IRQ pin
|
||||
|
#define P_LORA_NSS 10 //SX1262 SS pin
|
||||
|
#define P_LORA_RESET 5 //SX1262 Rest pin
|
||||
|
#define P_LORA_BUSY 4 //SX1262 Busy pin
|
||||
|
#define P_LORA_SCLK 12 //SX1262 SCLK pin
|
||||
|
#define P_LORA_MISO 13 //SX1262 MISO pin
|
||||
|
#define P_LORA_MOSI 11 //SX1262 MOSI pin
|
||||
|
|
||||
|
#define PIN_BOARD_SDA1 42 //SDA for PMU and PFC8563 (RTC)
|
||||
|
#define PIN_BOARD_SCL1 41 //SCL for PMU and PFC8563 (RTC)
|
||||
|
|
||||
|
#define PIN_PMU_IRQ 40 //IRQ pin for PMU
|
||||
|
|
||||
|
// #define PIN_GPS_RX 9
|
||||
|
// #define PIN_GPS_TX 8
|
||||
|
// #define PIN_GPS_EN 7
|
||||
|
|
||||
|
#define P_BOARD_SPI_MOSI 35 //SPI for SD Card and QMI8653 (IMU)
|
||||
|
#define P_BOARD_SPI_MISO 37 //SPI for SD Card and QMI8653 (IMU)
|
||||
|
#define P_BOARD_SPI_SCK 36 //SPI for SD Card and QMI8653 (IMU)
|
||||
|
#define P_BPARD_SPI_CS 47 //Pin for SD Card CS
|
||||
|
#define P_BOARD_IMU_CS 34 //Pin for QMI8653 (IMU) CS
|
||||
|
|
||||
|
#define P_BOARD_IMU_INT 33 //IMU Int pin
|
||||
|
#define P_BOARD_RTC_INT 14 //RTC Int pin
|
||||
|
|
||||
|
//I2C Wire addresses
|
||||
|
#define I2C_BME280_ADD 0x76 //BME280 sensor I2C address on Wire
|
||||
|
#define I2C_OLED_ADD 0x3C //SH1106 OLED I2C address on Wire
|
||||
|
#define I2C_QMC6310U_ADD 0x1C //QMC6310U mag sensor I2C address on Wire
|
||||
|
|
||||
|
//I2C Wire1 addresses
|
||||
|
#define I2C_RTC_ADD 0x51 //RTC I2C address on Wire1
|
||||
|
#define I2C_PMU_ADD 0x34 //AXP2101 I2C address on Wire1
|
||||
|
|
||||
|
#define PMU_WIRE_PORT Wire1 |
||||
|
#define RTC_WIRE_PORT Wire1 |
||||
|
#endif |
||||
|
|
||||
|
#ifdef TBEAM_SX1262 |
||||
|
#define P_LORA_BUSY 32 |
||||
|
#endif |
||||
|
|
||||
|
#ifdef TBEAM_SX1276 |
||||
|
#define P_LORA_DIO_2 32 |
||||
|
#define P_LORA_BUSY RADIOLIB_NC |
||||
|
#endif |
||||
|
|
||||
|
#if defined(TBEAM_SX1262) || defined(TBEAM_SX1276) |
||||
|
// LoRa radio module pins for TBeam
|
||||
|
// uint32_t P_LORA_BUSY = 0; //shared, so define at run
|
||||
|
// uint32_t P_LORA_DIO_2 = 0; //SX1276 only, so define at run
|
||||
|
|
||||
|
#define P_LORA_DIO_0 26 |
||||
|
#define P_LORA_DIO_1 33 |
||||
|
#define P_LORA_NSS 18 |
||||
|
#define P_LORA_RESET 23 |
||||
|
#define P_LORA_SCLK 5 |
||||
|
#define P_LORA_MISO 19 |
||||
|
#define P_LORA_MOSI 27 |
||||
|
|
||||
|
// #define PIN_GPS_RX 34
|
||||
|
// #define PIN_GPS_TX 12
|
||||
|
|
||||
|
#define PIN_PMU_IRQ 35 |
||||
|
#define PMU_WIRE_PORT Wire |
||||
|
#define RTC_WIRE_PORT Wire |
||||
|
#define I2C_PMU_ADD 0x34 |
||||
|
#endif |
||||
|
|
||||
|
// enum RadioType {
|
||||
|
// SX1262,
|
||||
|
// SX1276
|
||||
|
// };
|
||||
|
|
||||
|
class TBeamBoard : public ESP32Board { |
||||
|
XPowersLibInterface *PMU = NULL; |
||||
|
//PhysicalLayer * pl;
|
||||
|
//RadioType * radio = NULL;
|
||||
|
// int radioVersions = 2;
|
||||
|
|
||||
|
enum { |
||||
|
POWERMANAGE_ONLINE = _BV(0), |
||||
|
DISPLAY_ONLINE = _BV(1), |
||||
|
RADIO_ONLINE = _BV(2), |
||||
|
GPS_ONLINE = _BV(3), |
||||
|
PSRAM_ONLINE = _BV(4), |
||||
|
SDCARD_ONLINE = _BV(5), |
||||
|
AXDL345_ONLINE = _BV(6), |
||||
|
BME280_ONLINE = _BV(7), |
||||
|
BMP280_ONLINE = _BV(8), |
||||
|
BME680_ONLINE = _BV(9), |
||||
|
QMC6310_ONLINE = _BV(10), |
||||
|
QMI8658_ONLINE = _BV(11), |
||||
|
PCF8563_ONLINE = _BV(12), |
||||
|
OSC32768_ONLINE = _BV(13), |
||||
|
}; |
||||
|
|
||||
|
bool power_init(); |
||||
|
//void radiotype_detect();
|
||||
|
|
||||
|
public: |
||||
|
|
||||
|
#ifdef MESH_DEBUG |
||||
|
void printPMU(); |
||||
|
void scanDevices(TwoWire *w); |
||||
|
#endif |
||||
|
void begin(); |
||||
|
|
||||
|
#ifndef TBEAM_SUPREME_SX1262 |
||||
|
void onBeforeTransmit() override{ |
||||
|
digitalWrite(P_LORA_TX_LED, LOW); // turn TX LED on - invert pin for SX1276
|
||||
|
} |
||||
|
void onAfterTransmit() override{ |
||||
|
digitalWrite(P_LORA_TX_LED, HIGH); // turn TX LED off - invert pin for SX1276
|
||||
|
} |
||||
|
#endif |
||||
|
|
||||
|
void enterDeepSleep(uint32_t secs, int pin_wake_btn) { |
||||
|
esp_sleep_pd_config(ESP_PD_DOMAIN_RTC_PERIPH, ESP_PD_OPTION_ON); |
||||
|
|
||||
|
// Make sure the DIO1 and NSS GPIOs are hold on required levels during deep sleep
|
||||
|
rtc_gpio_set_direction((gpio_num_t)P_LORA_DIO_1, RTC_GPIO_MODE_INPUT_ONLY); |
||||
|
rtc_gpio_pulldown_en((gpio_num_t)P_LORA_DIO_1); |
||||
|
|
||||
|
rtc_gpio_hold_en((gpio_num_t)P_LORA_NSS); |
||||
|
|
||||
|
if (pin_wake_btn < 0) { |
||||
|
esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet
|
||||
|
} else { |
||||
|
esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1) | (1L << pin_wake_btn), ESP_EXT1_WAKEUP_ANY_HIGH); // wake up on: recv LoRa packet OR wake btn
|
||||
|
} |
||||
|
|
||||
|
if (secs > 0) { |
||||
|
esp_sleep_enable_timer_wakeup(secs * 1000000); |
||||
|
} |
||||
|
|
||||
|
// Finally set ESP32 into sleep
|
||||
|
esp_deep_sleep_start(); // CPU halts here and never returns!
|
||||
|
} |
||||
|
|
||||
|
uint16_t getBattMilliVolts(){ |
||||
|
return PMU->getBattVoltage(); |
||||
|
} |
||||
|
|
||||
|
const char* getManufacturerName() const{ |
||||
|
return "LilyGo T-Beam"; |
||||
|
} |
||||
|
}; |
||||
@ -0,0 +1,70 @@ |
|||||
|
[LilyGo_TBeam_SX1276] |
||||
|
extends = esp32_base |
||||
|
board = ttgo-t-beam |
||||
|
build_flags = |
||||
|
${esp32_base.build_flags} |
||||
|
-I variants/lilygo_tbeam_SX1276 |
||||
|
-D TBEAM_SX1276 |
||||
|
-D SX127X_CURRENT_LIMIT=120 |
||||
|
-D RADIO_CLASS=CustomSX1276 |
||||
|
-D WRAPPER_CLASS=CustomSX1276Wrapper |
||||
|
-D DISPLAY_CLASS=SSD1306Display |
||||
|
-D LORA_TX_POWER=20 |
||||
|
-D P_LORA_TX_LED=4 |
||||
|
-D PIN_BOARD_SDA=21 |
||||
|
-D PIN_BOARD_SCL=22 |
||||
|
-D PIN_GPS_RX=34 |
||||
|
-D PIN_GPS_TX=12 |
||||
|
-D PIN_USER_BTN=38 |
||||
|
-D ENV_INCLUDE_GPS=1 |
||||
|
;-D ENV_INCLUDE_BME680 |
||||
|
build_src_filter = ${esp32_base.build_src_filter} |
||||
|
+<../variants/lilygo_tbeam_SX1276> |
||||
|
+<helpers/ui/SSD1306Display.cpp> |
||||
|
+<helpers/esp32/TBeamBoard.cpp> |
||||
|
+<helpers/sensors> |
||||
|
board_build.partitions = min_spiffs.csv ; get around 4mb flash limit |
||||
|
lib_deps = |
||||
|
${esp32_base.lib_deps} |
||||
|
lewisxhe/XPowersLib@^0.2.7 |
||||
|
adafruit/Adafruit SSD1306 @ ^2.5.13 |
||||
|
stevemarple/MicroNMEA @ ^2.0.6 |
||||
|
boschsensortec/BSEC Software Library @ ^1.8.1492 |
||||
|
|
||||
|
[env:Tbeam_SX1276_companion_radio_ble] |
||||
|
extends = LilyGo_TBeam_SX1276 |
||||
|
board_build.upload.maximum_ram_size=2000000 |
||||
|
build_flags = |
||||
|
${LilyGo_TBeam_SX1276.build_flags} |
||||
|
-D MAX_CONTACTS=100 |
||||
|
-D MAX_GROUP_CHANNELS=8 |
||||
|
-D BLE_PIN_CODE=123456 |
||||
|
; -D BLE_DEBUG_LOGGING=1 |
||||
|
-D OFFLINE_QUEUE_SIZE=256 |
||||
|
; -D RADIOLIB_DEBUG_BASIC=1 |
||||
|
; -D MESH_PACKET_LOGGING=1 |
||||
|
; -D MESH_DEBUG=1 |
||||
|
build_src_filter = ${LilyGo_TBeam_SX1276.build_src_filter} |
||||
|
+<helpers/esp32/*.cpp> |
||||
|
+<../examples/companion_radio> |
||||
|
lib_deps = |
||||
|
${LilyGo_TBeam_SX1276.lib_deps} |
||||
|
densaugeo/base64 @ ~1.4.0 |
||||
|
|
||||
|
[env:Tbeam_SX1276_repeater] |
||||
|
extends = LilyGo_TBeam_SX1276 |
||||
|
build_flags = |
||||
|
${LilyGo_TBeam_SX1276.build_flags} |
||||
|
-D ADVERT_NAME='"Tbeam Repeater"' |
||||
|
-D ADVERT_LAT=0.0 |
||||
|
-D ADVERT_LON=0.0 |
||||
|
-D ADMIN_PASSWORD='"password"' |
||||
|
-D MAX_NEIGHBOURS=8 |
||||
|
-D PERSISTANT_GPS=1 |
||||
|
; -D MESH_PACKET_LOGGING=1 |
||||
|
; -D MESH_DEBUG=1 |
||||
|
build_src_filter = ${LilyGo_TBeam_SX1276.build_src_filter} |
||||
|
+<../examples/simple_repeater> |
||||
|
lib_deps = |
||||
|
${LilyGo_TBeam_SX1276.lib_deps} |
||||
|
${esp32_ota.lib_deps} |
||||
@ -0,0 +1,75 @@ |
|||||
|
#include <Arduino.h> |
||||
|
#include "target.h" |
||||
|
|
||||
|
TBeamBoard board; |
||||
|
|
||||
|
#if defined(P_LORA_SCLK) |
||||
|
static SPIClass spi; |
||||
|
RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_0, P_LORA_RESET, P_LORA_DIO_1, spi); |
||||
|
#else |
||||
|
RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_0, P_LORA_RESET, P_LORA_DIO_1); |
||||
|
#endif |
||||
|
|
||||
|
WRAPPER_CLASS radio_driver(radio, board); |
||||
|
|
||||
|
ESP32RTCClock fallback_clock; |
||||
|
AutoDiscoverRTCClock rtc_clock(fallback_clock); |
||||
|
|
||||
|
#if ENV_INCLUDE_GPS |
||||
|
#include <helpers/sensors/MicroNMEALocationProvider.h> |
||||
|
MicroNMEALocationProvider nmea = MicroNMEALocationProvider(Serial1); |
||||
|
EnvironmentSensorManager sensors = EnvironmentSensorManager(nmea); |
||||
|
#else |
||||
|
EnvironmentSensorManager sensors; |
||||
|
#endif |
||||
|
|
||||
|
#ifdef DISPLAY_CLASS |
||||
|
DISPLAY_CLASS display; |
||||
|
#endif |
||||
|
|
||||
|
#ifndef LORA_CR |
||||
|
#define LORA_CR 5 |
||||
|
#endif |
||||
|
|
||||
|
bool radio_init() { |
||||
|
fallback_clock.begin(); |
||||
|
rtc_clock.begin(Wire); |
||||
|
|
||||
|
#if defined(P_LORA_SCLK) |
||||
|
spi.begin(P_LORA_SCLK, P_LORA_MISO, P_LORA_MOSI); |
||||
|
#endif |
||||
|
int status = radio.begin(LORA_FREQ, LORA_BW, LORA_SF, LORA_CR, RADIOLIB_SX126X_SYNC_WORD_PRIVATE, LORA_TX_POWER, 8); |
||||
|
if (status != RADIOLIB_ERR_NONE) { |
||||
|
Serial.print("ERROR: radio init failed: "); |
||||
|
Serial.println(status); |
||||
|
return false; // fail
|
||||
|
} |
||||
|
|
||||
|
#ifdef SX127X_CURRENT_LIMIT |
||||
|
radio.setCurrentLimit(SX127X_CURRENT_LIMIT); |
||||
|
#endif |
||||
|
|
||||
|
radio.setCRC(1); |
||||
|
|
||||
|
return true; // success
|
||||
|
} |
||||
|
|
||||
|
uint32_t radio_get_rng_seed() { |
||||
|
return radio.random(0x7FFFFFFF); |
||||
|
} |
||||
|
|
||||
|
void radio_set_params(float freq, float bw, uint8_t sf, uint8_t cr) { |
||||
|
radio.setFrequency(freq); |
||||
|
radio.setSpreadingFactor(sf); |
||||
|
radio.setBandwidth(bw); |
||||
|
radio.setCodingRate(cr); |
||||
|
} |
||||
|
|
||||
|
void radio_set_tx_power(uint8_t dbm) { |
||||
|
radio.setOutputPower(dbm); |
||||
|
} |
||||
|
|
||||
|
mesh::LocalIdentity radio_new_identity() { |
||||
|
RadioNoiseListener rng(radio); |
||||
|
return mesh::LocalIdentity(&rng); // create new random identity
|
||||
|
} |
||||
@ -0,0 +1,27 @@ |
|||||
|
#pragma once |
||||
|
|
||||
|
#define RADIOLIB_STATIC_ONLY 1 |
||||
|
//#include <RadioLib.h>
|
||||
|
#include <helpers/RadioLibWrappers.h> |
||||
|
#include <helpers/esp32/TBeamBoard.h> |
||||
|
#include <helpers/CustomSX1276Wrapper.h> |
||||
|
#include <helpers/AutoDiscoverRTCClock.h> |
||||
|
#include <helpers/sensors/EnvironmentSensorManager.h> |
||||
|
#ifdef DISPLAY_CLASS |
||||
|
#include <helpers/ui/SSD1306Display.h> |
||||
|
#endif |
||||
|
|
||||
|
extern TBeamBoard board; |
||||
|
extern WRAPPER_CLASS radio_driver; |
||||
|
extern AutoDiscoverRTCClock rtc_clock; |
||||
|
extern EnvironmentSensorManager sensors; |
||||
|
|
||||
|
#ifdef DISPLAY_CLASS |
||||
|
extern DISPLAY_CLASS display; |
||||
|
#endif |
||||
|
|
||||
|
bool radio_init(); |
||||
|
uint32_t radio_get_rng_seed(); |
||||
|
void radio_set_params(float freq, float bw, uint8_t sf, uint8_t cr); |
||||
|
void radio_set_tx_power(uint8_t dbm); |
||||
|
mesh::LocalIdentity radio_new_identity(); |
||||
Loading…
Reference in new issue